- Out of stock
Kingston 8GB Kit (2 x 4GB), DDR3, 1333MHz (PC3-10600), CL9, DIMM Memory
£64.87
VAT included
8GB (4GB 1Rx8 512M x 64-Bit x 2 pcs.) PC3-10600 CL9 240-Pin DIMM Kit
ValueRAM's KVR13N9S8K2/8 is a kit of two 512M x 64-bit (4GB) DDR3-1333 CL9 SDRAM (Synchronous DRAM), 1Rx8, memory modules, based on eight 512M x 8-bit FBGA components per module. Total kit capacity is 8GB. The SPDs are programmed to JEDEC standard latency DDR3-1333 timing of 9-9-9 at 1.5V. Each 240-pin DIMM uses gold contact fingers.
Features
• JEDEC standard 1.5V (1.425V ~1.575V) Power Supply
• VDDQ = 1.5V (1.425V ~ 1.575V)
• 667MHz fCK for 1333Mb/sec/pin
• 8 independent internal bank
• Programmable CAS Latency: 9, 8, 7, 6
• Programmable Additive Latency: 0, CL - 2, or CL - 1 clock
• Programmable CAS Write Latency(CWL) = 7 (DDR3-1333)
• 8-bit pre-fetch
• Burst Length: 8 (Interleave without any limit, sequential with
starting address “000” only), 4 with tCCD = 4 which does not
allow seamless read or write [either on the fly using A12 or
MRS]
• Bi-directional Differential Data Strobe
• Internal(self) calibration : Internal self calibration through ZQ
pin (RZQ : 240 ohm ± 1%)
• On Die Termination using ODT pin
• Average Refresh Period 7.8us at lower than TCASE 85°C,
3.9us at 85°C < TCASE < 95°C
• Asynchronous Reset
• PCB: Height 0.740” (18.75mm), single sided component
Description
Specification
- Series: Kingston ValueRAM
- DDR Type: DDR3
- Size: 2 x 4GB
- Speed: 1333 MHz
- Compliance: PC3-10600
- Pins: 240-pin
- CAS Latency: CL9
- Data Integrity Check: Non-ECC
- Heatsink: No
- Additional Information: Single rank
Unbuffered - Package Type: Blister Pack
- Package Weight: 0.0380 kg
- Warranty: Lifetime
KVR13N9S8K2/8
Data sheet
- Warranty
- Lifetime
- DDR Type
- DDR3
- Package Type
- Blister Pack
- Package Weight
- 0.0380 kg
- Heatsink
- No
- Series
- Kingston ValueRAM
- Size
- 2 x 4GB
- Speed
- 1333 MHz
- Compliance
- PC3-10600
- Pins
- 240-pin
- CAS Latency
- CL9
- Data Integrity Check
- Non-ECC
- Additional Information
- Single rank , Unbuffered
Specific References
- EAN13
- 740617216967
Comments (0)
No customer reviews for the moment.
8GB (4GB 1Rx8 512M x 64-Bit x 2 pcs.) PC3-10600 CL9 240-Pin DIMM Kit
ValueRAM's KVR13N9S8K2/8 is a kit of two 512M x 64-bit (4GB) DDR3-1333 CL9 SDRAM (Synchronous DRAM), 1Rx8, memory modules, based on eight 512M x 8-bit FBGA components per module. Total kit capacity is 8GB. The SPDs are programmed to JEDEC standard latency DDR3-1333 timing of 9-9-9 at 1.5V. Each 240-pin DIMM uses gold contact fingers.
Features
• JEDEC standard 1.5V (1.425V ~1.575V) Power Supply
• VDDQ = 1.5V (1.425V ~ 1.575V)
• 667MHz fCK for 1333Mb/sec/pin
• 8 independent internal bank
• Programmable CAS Latency: 9, 8, 7, 6
• Programmable Additive Latency: 0, CL - 2, or CL - 1 clock
• Programmable CAS Write Latency(CWL) = 7 (DDR3-1333)
• 8-bit pre-fetch
• Burst Length: 8 (Interleave without any limit, sequential with
starting address “000” only), 4 with tCCD = 4 which does not
allow seamless read or write [either on the fly using A12 or
MRS]
• Bi-directional Differential Data Strobe
• Internal(self) calibration : Internal self calibration through ZQ
pin (RZQ : 240 ohm ± 1%)
• On Die Termination using ODT pin
• Average Refresh Period 7.8us at lower than TCASE 85°C,
3.9us at 85°C < TCASE < 95°C
• Asynchronous Reset
• PCB: Height 0.740” (18.75mm), single sided component